Items (0)
£0.00

Hobbywing LED Program Box PC2A - for PLATINUM series Aircraft & Helicoptor ESC's

  code:LED_PC2A
  • Offers Available
  • Buy 3 or more items for 5% off (use code 5%OFF at the shopping basket)
£9.99 (Delivery from £0.99)
Item in Stock  |  Usually dispatched within 24 hours
Add to Bag
This product has been added to your basket...
  • Continue Shopping
  • Checkout

LED Program Box PC2A - for PLATINUM series Aircraft & Helicoptor ESC's

HobbyWing Program Box for the PLATINUM series ESC's.

This pocket size LED display programmer is for the PLATINUM series of Aircraft / Helicopter ESC's from Hobbywing. Note - It is not suitable for RC Car or boat ESC's.


Hobbywing make these is 3 variants.
LED_PC2A - Is for Aircraft (PLATINUM series) - This Item
LED_PC2B - IS for Boats (SEAKING series)
LED_PC2C - Is for Cars (EZRUN & XERUN series)

So what does it do?

It lets your quickly and easily see, and change the programmable settings in your brushless speed controller without having to use the small 'SET' button and manual, making quick changes a breeze. An instruction manual is supplied with the unit.

 


1. Specification:

1.1 Size:88mm (L) * 58mm (W) * 14mm (H)
1.2 Weight:40g.
1.3 Input Voltage: 4.8-6V (If the ESC hasn`t a built-in BEC, you must use an additional battery pack to supply the program card) Please pay attention to the connections as connecting incorrectly will damage the programmer and will not be covered under warrentee.

2. Programmable Items:


The programmable items of LED_PC2A (Available for PLATINUM series of ESC's)
#1 Brake
#2 Battery Type
#3 Cutoff Mode
#4 Low Voltage Threshold
#5 Start Mode
#6 Advanced Timing
#7 Goveror Mode
#8 Reserved
#9 PWM frequency
#10 BEC Output Voltage
#11 Reserved
#12 Lipo Cells

Connecting up to your ESC

Most ESC's have a built in BEC circuit which can be used to power the Program card directly. i.e. you don't need a seperate battery or supply.
On the top of the programmer there are 2 connections. The one nearest the edge is the connection to the ESC. The other is not usually required. Check the orientation of the connector is correct. (The white signal wire goes nearest to the edge and is marked on the programmer)


Start with the battery disconnected and make sure the ESC switch is OFF

Remove the ESC wire from the receiver and plug it into the programmer as stated above.
When you turn on the ESC's power it will power up the programmer after a couple of seconds displaying Item #1 and its current setting. (Note: it takes around 3 seconds to communicate with the esc before powering up).

You can now check through the current settings with the 'ITEM' button and alter the parameter settings using the 'VALUE' buton. Press the 'OK'button to save the change of each item. Use the guide on the front panel for Item and parameter reference.

When done, turn off the ESC power, disconnect the models battery. Now re fit the ESC wire back into the receiver. (nornally Channel 2)

Your now done. 

 

 

Specification:

MPN# 86020020

1.1 Size:88mm (L) * 58mm (W) * 14mm (H)
1.2 Weight:40g.
1.3 Input Voltage: 4.8-6V (If the ESC hasn`t a built-in BEC, you must use an additional battery pack to supply the program card) Please pay attention to the connections as connecting incorrectly will damage the programmer and will not be covered under warrentee.

An instruction manual is supplied with this item, however you can  download the manual from the manufacturers website here:

Be the first to review Hobbywing LED Program Box PC2A - for PLATINUM series Aircraft & Helicoptor ESC's. Write a review ›