Items (0)
£0.00

Hobbywing LED Programmer PC2C for XERUN, QUICRUN & EZRUN RC Car ESC's (V2)

  code:LED_PC2C
  • Offers Available
  • Buy 3 or more items for 5% off (use code 5%OFF at the shopping basket)
£9.99 (Delivery from £0.99)
Item in Stock  |  Usually dispatched within 24 hours
Add to Bag
This product has been added to your basket...
  • Continue Shopping
  • Checkout

Hobbtwing ESC Programmer for XERUN, QUICRUN and EZRUN RC Car ESC's (V2)

This pocket size programmer is for the XERUN, QUICRUN and EZRUN series (Version 2.0or higher) car ESC's including the ESC sold at RC Hobby Centre. This model is not suitable for the ESC's used in Heli's, planes or boats.Hobbywing make these is 3 variants.

LED_PC2A - Is for Aircraft (PLATINUM series)
LED_PC2B - IS for Boats (SEAKING series)
LED_PC2C - Is for Cars (EZRUN, QUICRUN & XERUN series) THIS ONE

So what does it do?

It lets your quickly and easily see, and change the programmable settings in your brushless speed controller without having to use the small 'SET' button and manual, making quick changes a breeze. An instruction manual is supplied with the unit.


1. Specification:

1.1 Size:88mm (L) * 58mm (W) * 14mm (H)
1.2 Weight:40g.
1.3 Input Voltage: 4.8-6V (If the ESC hasn`t got a built-in BEC, you must use an additional battery pack to supply the program card) Please pay attention to the connections as connecting incorrectly will damage the programmer and will not be covered under warrentee.

2. Programmable Items:


The programmable items of LED_PC2C(Available for XERUN, QUICRUN and EZRUN series car ESC of Version2 or higher)
#1 Running mode
#2 Drag Brake Force
#3 Low voltage Cut-Off Threshold
#4 Start Mode
#5 Maximum Brake Force
#6 Maximum Reverse Force
#7 Initial Brake Force
#8 Throttle Neutral Range
#9 Timing
#10 Over-Heat Protection
#11 Motor Rotation
#12 Lipo Cells
(Note: The item #11 and #12 are not available for XERUN series ESC of Version 2, they are only available for EZRUN series ESC)

Connecting up the program card to your ESC

Most ESC's have a built in BEC circuit which can be used to power the Program card directly. i.e. you don't need a seperate battery or supply.
On the top of the programmer there are 2 connections. The one nearest the edge is the connection to the ESC. The other is not usually required. Check the orientation of the connector is correct. (The white signal wire goes nearest to the edge and is marked on the programmer)


Start with the battery disconnected and make sure the ESC switch is OFF

Remove the ESC wire from the receiver and plug it into the programmer as stated above.
When you turn on the cars power it will power up the programmer after a couple of seconds displaying Item #1 and its current setting. (Note: they is a delay of around 3 seconds for the programmer to power up)

You can now check through the current settings with the 'ITEM' button and alter the parameter setting using the 'VALUE' buton. Press the 'OK'button to save the change of each item. Use the guide on the front panel for Item and parameter reference.

When done, turn off the cars power, disconnect the car battery. Now re fit the ESC wire back into the receiver. (nornally Channel 2)

Your now done. 

The instruction manual is included with the item, or you can download the latest instruction manual from Hobbywing  here:

or Download Manual from RC Hobby Centre.

Specification:

MPN# 86020010

  • Size:88mm (L) * 58mm (W) * 14mm (H)
  • Weight:40g.
  • Input Voltage: 4.8-6V (If the ESC hasn`t a built-in BEC, you must use an additional battery pack to supply the program card) Please pay attention to the connections as connecting incorrectly will damage the programmer and will not be covered under warrentee.

Used for programming HobbyWing XERUN and EZRUN series of ESC's

Firmware Version V2

Download Manual

Be the first to review Hobbywing LED Programmer PC2C for XERUN, QUICRUN & EZRUN RC Car ESC's (V2). Write a review ›